AutoMotoFoto.com Galerija   indivisual studio
 Peugeot 307 Breaknck 
I decided to go full-on with the audio system, so I got a matching subwoofer for my front speakers - Focal 33KX - 13-inch subwoofer in a custom sealed enclosure.
I decided to go full-on with the audio system, so I got a matching subwoofer for my front speakers - Focal 33KX - 13-inch subwoofer in a custom sealed enclosure.
Viewed: 5493 times.

Kevlar membrane, dual voice coil, multiple magnets and the enclosure with more volume than my last one - sounds amazing! :-)
Kevlar membrane, dual voice coil, multiple magnets and the enclosure with more volume than my last one - sounds amazing! :-)
Viewed: 6108 times.

Cheap chinese rear parking sensors off eBay - a bit "paranoid" (i.e. too sensitive) but should do their job.
Cheap chinese rear parking sensors off eBay - a bit "paranoid" (i.e. too sensitive) but should do their job.
Viewed: 5593 times.

A hole for routing the sensor cables inside the boot - I'll put the module in the side pocket or behind the side panel.
A hole for routing the sensor cables inside the boot - I'll put the module in the side pocket or behind the side panel.
Viewed: 5584 times.

Sensors location marked, based on my interpretation of the fitting instuctions.
Sensors location marked, based on my interpretation of the fitting instuctions.
Viewed: 5529 times.

Drilling the bumper with the supplied drill-bit.
Drilling the bumper with the supplied drill-bit.
Viewed: 5527 times.

A couple of holes had to be cut in the steel bar behind the bumper, for the inner pair of parking sensors to sit in.
A couple of holes had to be cut in the steel bar behind the bumper, for the inner pair of parking sensors to sit in.
Viewed: 5595 times.

Peugeot had already made a couple of holes for this reason, but unfortunately their sensor arrangement was different to mine.
Peugeot had already made a couple of holes for this reason, but unfortunately their sensor arrangement was different to mine.
Viewed: 5590 times.

Then I turned my attention to removing the front bumper - not to install parking sensors, but to change the headlights (not too clever a design)!
Then I turned my attention to removing the front bumper - not to install parking sensors, but to change the headlights (not too clever a design)!
Viewed: 9876 times.

I wanted black headlights but decided against spraying my own set, so I got a brand new pair of black aftermarket headlights.
I wanted black headlights but decided against spraying my own set, so I got a brand new pair of black aftermarket headlights.
Viewed: 7590 times.

I chose the rare version with OE-style reflectors, instead of small HID-style lenses (that everybody seems to go for).
I chose the rare version with OE-style reflectors, instead of small HID-style lenses (that everybody seems to go for).
Viewed: 6268 times.

They've got "angel eyes" or "halo rings" - perhaps a bit tacky, but they don't look bad and they're barely visible in daylight anyway.
They've got "angel eyes" or "halo rings" - perhaps a bit tacky, but they don't look bad and they're barely visible in daylight anyway.
Viewed: 9889 times.

Then I "bit the bullet" and finally made up my mind about spraying the exterior trim in white, so I removed all of the black trim.
Then I "bit the bullet" and finally made up my mind about spraying the exterior trim in white, so I removed all of the black trim.
Viewed: 7014 times.

Temporarily swapped the TSWs for my father's 406 Coupe Hoggars (7x16" ET12 - nice and wide) :-).
Temporarily swapped the TSWs for my father's 406 Coupe Hoggars (7x16" ET12 - nice and wide) :-).
Viewed: 6459 times.

Work in progress, but you can get an idea of what it will look like.
Work in progress, but you can get an idea of what it will look like.
Viewed: 5862 times.

While I was at it, I decided to completely respray the rear bumper. Looks kind of cool without it anyway :-).
While I was at it, I decided to completely respray the rear bumper. Looks kind of cool without it anyway :-).
Viewed: 5914 times.

Powered by Gallery v1